AUTONET TV

TCB your PCV (PCV Valve Replacement)

Your gasoline engine goes through some exhausting work.  Yes, it's truly exhausting, as in: it produces exhaust! And when your engine starts behaving like it's exhausted, such as running poorly or getting lousy fuel economy, the trouble may be something called a PCV valve.

Did you know it's a series of explosions that creates the power in your engine? The spark plugs ignite a mixture of gasoline and air and BANG! A whole bunch of those and you're engine is humming away. Leftover vapors from those explosions go into your crankcase, which is also a place where engine oil goes.  Those vapors still have a lot of unburned fuel in them, and if they had nowhere to go, they'd turn your oil into a thick mess called sludge, not good for a smooth running engine. 

Engineers came up with an idea. Re-direct those gasses building up in the crankcase into the engine's air intake and mix them with fresh air.  That way the unburned fuel could go through the engine again and produce power. It also means the unburned fuel doesn't pollute the air.  The part that makes that happen is called the Positive Crankcase Ventilation (PCV) valve.

Besides reducing pollution and preventing the oil from turning to sludge, the PCV valve also relieves pressure in the crankcase, reducing the potential for oil to leak. One of the reasons you should get your oil changed as frequently as your vehicle's manufacturer recommends is that it helps reduce chances for problems with the PCV valve.

After a while, the PCV valve can itself get gummed up and stick, and the driver may notice oil leaks, reduced power or engine hesitation.  That's why it's important to make sure the PCV valve is operating like it should, and often it can be diagnosed during a visual inspection by our technicians.  Replacing a PCV valve is usually quick and inexpensive.  After it's done, your vehicle will run with the performance and fuel economy you're used to.  Goodbye exhaustion!

Union Street Automotive
175 W Union Street
Newark, NY 14513
315-331-2525
http://www.unionstreetautomotive.net

Clean Machine (Fuel and Air Induction Cleaning)

As your vehicle ages, its performance isn’t quite what it used to be, but many of us never notice the change because it’s gradual.  So here are a few questions to ask yourself.  Does your vehicle feel like it doesn’t have the pep that it used to? Have you noticed your fuel economy isn’t quite as good as it once was? Does it idle roughly or is it hard to start?  Do you hear the engine knocking? Has it recently failed an emissions test?

All of those can be signs that your fuel and air induction systems are dirty and need cleaning.  Your fuel system takes gasoline from the tank to the engine’s combustion chambers where fuel injectors spray fuel that mixes with air and is ignited by spark plugs.  Black carbon deposits eventually can build up, obstructing fuel flow and diminishing your engine’s performance and fuel efficiency.

The air induction system is what allows air to go into the engine’s combustion chamber.  Getting the proper air flow is necessary for you to quickly start your vehicle, accelerate, and perform the way it should and idle smoothly when you’re standing still.  Like the fuel system, your air induction system can get blocked up with deposits and other contaminants.

A professional fuel and air induction cleaning can help restore your performance and fuel economy, especially when you are experiencing problems.  A technician will use specialized chemicals that can remove the carbon buildup.  In extreme cases, they will remove the fuel injectors and clean them with specialized tools.  

After cleaning, you may notice how much more pep your vehicle has and how smoothly it runs.  Keep your fuel and air induction systems clean and enjoy your vehicle’s performance improvements.

Union Street Automotive
175 W Union Street
Newark, NY 14513
315-331-2525
http://www.unionstreetautomotive.net

A Not-So-Straight Story (Vehicle Pulls to One Side)

A vehicle should travel straight down a straight road with the steering wheel centered.  But time and travel can take their toll and soon you may find your vehicle pulling to the left or right.  Those are not good signs and should be taken care of fairly quickly.

One thing that you should note is when this is happening: if it is all the time, only when you brake, only when you accelerate. If you describe these symptoms to the service adviser or technician, it may help them pinpoint the cause more quickly. 

Many things can cause a vehicle to pull to one side, one of which is that it's out of alignment.  If so, you could be doing damage to other components of your vehicle if you keep driving with it this way. If your tires show signs of uneven wear on the treads or if your wheels squealing, that is another clue.

Improperly inflated tires can also cause your vehicle to pull in one direction.  Your service facility can check to see if your tires have the pressure recommended by your vehicle's manufacturer. 

When steering linkage wears out or a wheel bearing goes bad, both of those can cause a vehicle not to track straight. When components age and loosen up, they can present a safety hazard and premature tire wearing. 

Maybe you notice the pulling only when you are braking.  That points to a failure of your braking system, perhaps a sticky brake caliper.

When your vehicle was brand new, it went straight unless you guided it on a different path. It's best to have it checked out if it is showing some of these symptoms.  It could save you money in the long run and you'll be driving a safer, better performing vehicle.  That's what they mean by steering you right!

Union Street Automotive
175 W Union Street
Newark, NY 14513
315-331-2525
http://www.unionstreetautomotive.net

Stopping "Brake" Downs (Brake Pad Replacement)

If someone tells you to put the brakes on something, you know it means stop.  And stopping is one of the most important safety maneuvers you can do in any vehicle.  That means your brakes have to work properly. 

Let's face it.  You stop dozens of times every time you drive.  And over time, that takes its toll on your brakes.  Friction is what stops your vehicle.  Most newer vehicles have disc brakes, and the parts that wear out the fastest are those that rub against each other every time you stop, the rotors and the pads.

The rotors are discs that rotate with the wheels, and the pads are removable surfaces that make contact with the rotors to slow or stop your vehicle.  Bits of both wear off each time you stop, and when enough of either (or both) lose too much material, your brakes become unable to safely slow or stop your vehicle. 

The pads usually are the parts that wear out first.  Signs that your brakes might be getting worn are:

• You hear grinding, squeaking, or clicking when you apply them
• It takes a longer distance to stop
• Your pedal vibrates when you brake
• The front of your vehicle pulls to one side when you brake

If you notice any of these, bring your car to us so we can have a technician inspect your brakes. Most brake pads have a wear indicator that indicates it's time they should be replaced.  The technician who is checking things out will also look at your rotors for wear, as well as other brake system components.

With regular inspections and maintenance, you'll be sure that when you need to stop, your vehicle will be up to the task.

Union Street Automotive
175 W Union Street
Newark, NY 14513
315-331-2525
http://www.unionstreetautomotive.net

Stopping "Brake" Downs (Brake Pad Replacement)

If someone tells you to put the brakes on something, you know it means stop.  And stopping is one of the most important safety maneuvers you can do in any vehicle.  That means your brakes have to work properly. 

Let's face it.  You stop dozens of times every time you drive.  And over time, that takes its toll on your brakes.  Friction is what stops your vehicle.  Most newer vehicles have disc brakes, and the parts that wear out the fastest are those that rub against each other every time you stop, the rotors and the pads.

The rotors are discs that rotate with the wheels, and the pads are removable surfaces that make contact with the rotors to slow or stop your vehicle.  Bits of both wear off each time you stop, and when enough of either (or both) lose too much material, your brakes become unable to safely slow or stop your vehicle. 

The pads usually are the parts that wear out first.  Signs that your brakes might be getting worn are:

• You hear grinding, squeaking, or clicking when you apply them
• It takes a longer distance to stop
• Your pedal vibrates when you brake
• The front of your vehicle pulls to one side when you brake

If you notice any of these, bring your car to us so we can have a technician inspect your brakes. Most brake pads have a wear indicator that indicates it's time they should be replaced.  The technician who is checking things out will also look at your rotors for wear, as well as other brake system components.

With regular inspections and maintenance, you'll be sure that when you need to stop, your vehicle will be up to the task.

Union Street Automotive
175 W Union Street
Newark, NY 14513
315-331-2525
http://www.unionstreetautomotive.net